|
Before you can use NetDotCom to connect to the Internet you must have a NetDotCom Internet Access Account. Follow the instructions below to setup Windows 2000 for use with NetDotCom.
Click on Start, then Run, in the Open space provided, type inetwiz then click the OK button
Please click Connect using my phone line, then click Next. Note: In some instances another screen will appear before the one shown below. Choose the third option
"I want to set up my Internet connection manually..." and click next. Click on the Next button to continue.
Type in one of the phone numbers listed below, then click Next. You can also use NetDotComs' Number Finder to locate access numbers in other areas.
IMPORTANT:
Please use a number that is a local call from your location. If you do not know which number to select, please call NetDotCom for assistance or check with your telephone company operator.
Dial "0" (zero) and ask the operator if there is a charge to dial the number selected. IMPORTANT! NetDotCom will not be responsible if your choice results in toll
charges appearing of your phone bill.
 |
Regional Dial-Up Access Numbers |
 |
| Ashtabula |
440-344-0005 |
| Brookfield - Sharon |
330-969-0005 |
| Burton |
440-273-0023 |
| East Liverpool |
330-303-4050 |
| Niles |
330-299-4022 |
| Kent |
330-593-1000 |
| Kent |
330-541-0005 |
| Kinsman |
330-355-0005 |
| Parkman |
440-271-0005 |
| Ravenna |
330-577-5010 |
| Salem/Lisbon |
330-964-0005 |
| Warren |
330-442-0005 |
| Warren |
330-984-4055 |
| Youngstown |
330-270-2060 |
| Youngstown |
330-423-4055 |
| Youngstown |
330-599-0005 |
| Youngstown |
330-884-6219 |
|
Type in your NetDotCom User name and Password in the appropriate spaces below, then click Next.
For security reasons your password will show up as stars so please type carefully.
Please type in all small letters without any spaces or punctuation marks or symbols.
Type in NetDotCom for the Connection name, then click Next.
Click Yes to set up your E-mail account, then click Next.
In some instances you will be shown the screen below and asked to create a new account or use an existing account, If not proceed to the next step.
If the account listed is a NetDotCom account and your only confirming or changing settings select "Use an existing Internet Mail account". Otherwise select Create a new
Internet mail account then click Next. If the old account is no longer used you should remove it from Outlook Express
to prevent errors when sending or receiving e-mail.
If you selected "Use an existing Internet Mail account" the screen below allows you to confirm the account settings. Click Next to continue.
In "Display Name" type in the name that you want to appear on all messages you send out then click Next. This can be a nickname, initials or
your real name. This name is not the same as your email address, which is typed in on the next step.
Type in your e-mail address exactly as given to you by NetDotCom. Normally it should be in all small letters, however you can use capitals to make it easier to read. No spaces are
permitted. Click Next to proceed.
On the "E-mail Server Names" screen, select POP3 for the type of incoming server.
Next, the Incoming and Outgoing mail server names need to be typed in. The following table indicates the proper mail server name to use based on your selected NetDotCom
e-mail address. After the information is entered, click Next to proceed.
|
|
E-mail address to server name mapping
|
|
|
If your e-mail address ends with
|
Type in this mail server name |
|
@netdotcom.com
|
mail.netdotcom.com
|
|
@ndcis.com
|
mail.ndcis.com
|
|
@digitaldrive.net
|
mail.digitaldrive.net
|
|
Any other domain name
|
mail.ndcis.net
|
In the "Account name" space, please type in your e-mail address and password exactly as given to you by NetDotCom. This must be typed in all small letters
without any spaces. Any mistakes will prevent you from retrieving e-mail sent to you. The 'check boxes' should be selected as shown. Click Next to proceed.
Click Finish to complete the Internet Connection Wizard. If this is the first time using the Internet Connection Wizard there will be a "check box" which allows you to
connect immediately if checked. If you check the box you are shown the next screen if not you are returned to Windows.
This completes the setup for Windows 2000.
|
